With all of the Schwintek slide motor issues, I'm wondering how many carry a spare motor? They are available online for a couple hundred dollars, and it certainly would be nice to have should one of the motors die while in the middle of nowhere. Is it over-kill?
Announcement
Collapse
No announcement yet.
Carry spare Schwintek motor?
Collapse
X
-
Originally posted by Lonestar View PostWith all of the Schwintek slide motor issues, I'm wondering how many carry a spare motor? They are available online for a couple hundred dollars, and it certainly would be nice to have should one of the motors die while in the middle of nowhere. Is it over-kill?
Jim
-
Thanks Jim,
I recently had an issue I thought was a motor, but turned out to be a harness that slipped out the frame and was chewed up by the tire. Got me thinking about the possibility of needing a motor on the spur of the minute.
I'm going to repair the harness. I cannot believe they charge $70 for a 20' small wire 5 conductor cable.
Jerry2020 Reflection 273MK
2005 Dodge Ram 2500 CTD
Comment
-
Originally posted by Lonestar View PostThanks Jim,
I recently had an issue I thought was a motor, but turned out to be a harness that slipped out the frame and was chewed up by the tire. Got me thinking about the possibility of needing a motor on the spur of the minute.
I'm going to repair the harness. I cannot believe they charge $70 for a 20' small wire 5 conductor cable.
Jerry
https://www.camperid.com/lippert/25-...pn-238991.html
Jim
Comment
-
I have replaced 3 motor's. Each time I was able to get a new motor in a timely manor. I have also retracted a slide with one motor out. As a result I don't carry a spare. I figure if it goes out while boondocking I will just retract the slide manually and put a 2x4 to hold it in.2017 Momentum 376, 2019 Ford F450
2022 Triumph Scrambler Motorcycle
E-bikes, Hobi Pedal Kayaks
Kota the dog and KC the Kitty Cat
Comment
-
Originally posted by d2reid View PostI have replaced 3 motor's. Each time I was able to get a new motor in a timely manor. I have also retracted a slide with one motor out. As a result I don't carry a spare. I figure if it goes out while boondocking I will just retract the slide manually and put a 2x4 to hold it in.
Jim
Comment
-
Jim,
That's a good point, however I wonder if Lippert is constantly changing the design. With the number of failures still going on, it doesn't appear any improvements are going on.
With all the junk components being used, GD included, you got to wonder what's going on. Is the small motor just under too much stress? I know it produces a lot of torque, so does that shorten the lifespan?
The old conventional electric through the frame units would last a long time, and offered the benefits of a manual crank in case of failure. Too bad Schwintek had to come along and ruin that.2020 Reflection 273MK
2005 Dodge Ram 2500 CTD
Comment
-
Originally posted by d2reid View PostI have replaced 3 motor's. Each time I was able to get a new motor in a timely manor. I have also retracted a slide with one motor out. As a result I don't carry a spare. I figure if it goes out while boondocking I will just retract the slide manually and put a 2x4 to hold it in.
I pulled the "bad motor" cable lead off the controller then had 3 guys help me push the slide in. I already had all power (AC and DC) disconnected from the trailer, but Lippert still said disconnect the lead. I strongly questioned that but complied anyway, and we got the slide back in the trailer.
After that, I just reconnected the lead to activate the motor brake, and had no trouble on the way home with the slide moving.
A mobile tech I called said the bad motor would have to be removed the retract the slide. Glad I did not have to do that, but now after getting into the slide mechanism, I could do that if absolutely necessary. I probably would have to do that if I didn't have any help to push the slide in.2020 Reflection 273MK
2005 Dodge Ram 2500 CTD
Comment
-
Originally posted by Lonestar View PostJim,
That's a good point, however I wonder if Lippert is constantly changing the design. With the number of failures still going on, it doesn't appear any improvements are going on.
With all the junk components being used, GD included, you got to wonder what's going on. Is the small motor just under too much stress? I know it produces a lot of torque, so does that shorten the lifespan?
The old conventional electric through the frame units would last a long time, and offered the benefits of a manual crank in case of failure. Too bad Schwintek had to come along and ruin that.
I believe the Schwintek system is a clever design and if set up properly I believe it could be reliable. There have been two major motor re-designs from what I see and a third mod to wrap the motor in shrink wrap which did not work for me. Clearance was so tight, the shrink wrap could not be used. If the larger slides are failing, it may be best that they all utilize the 500:1 units rather than the 300:1 units like I have on the large slide on the Imagine.
Failures can vary where my unit after being serviced twice and checked our by the GD repair center failed shortly after while being retracted and it would not move without a couple large fellows pushing on it to gain access to the motor attachment screw. A better method from GDRV to access this screw should be done asap and Lippert should be working to provide better longevity to the system before its reputation is beyond repair. But there is always that old technique of providing those improvements and calling it something different.
Two failure modes stand out. Torn or chafed wires at the motor or a failed motor.
Jim
Comment
-
Originally posted by Lonestar View PostWhat procedure did you use to retract your slide?
.
The second one I pulled the truck up next to the slide in a way that I could stand on the bed rail and get my legs and shoulder into the process while my wife "bumped" the other motor. She would slide it with the motor about an inch, I would struggle to catch up. Very slow.
Third time I removed the motor and was able to just tug from the inside while my wife operated the slide control.
Three failures in four years. I can't say that I am a fan of Schwintek slides. Guest comment about "and if properly set up" rings a bell for me. My left front slide is my problem child. I have ongoing issues with it. While my bedroom slide has been trouble free.
2017 Momentum 376, 2019 Ford F450
2022 Triumph Scrambler Motorcycle
E-bikes, Hobi Pedal Kayaks
Kota the dog and KC the Kitty Cat
Comment
-
Originally posted by MidwestCamper View Post
Lonestar,
I believe the Schwintek system is a clever design and if set up properly I believe it could be reliable. There have been two major motor re-designs from what I see and a third mod to wrap the motor in shrink wrap which did not work for me. Clearance was so tight, the shrink wrap could not be used. If the larger slides are failing, it may be best that they all utilize the 500:1 units rather than the 300:1 units like I have on the large slide on the Imagine.
Failures can vary where my unit after being serviced twice and checked our by the GD repair center failed shortly after while being retracted and it would not move without a couple large fellows pushing on it to gain access to the motor attachment screw. A better method from GDRV to access this screw should be done asap and Lippert should be working to provide better longevity to the system before its reputation is beyond repair. But there is always that old technique of providing those improvements and calling it something different.
Two failure modes stand out. Torn or chafed wires at the motor or a failed motor.
Jim
It seems that since the Schwintek system has now been used in trailers for several years, there would have been some attempt to make them more reliable overall. GDRV owns this problem, and they are the ones that should fix it or go with another mechanism on their trailers. I would not say that if it were just you and I having these issues, but it's lots of folks on the forums.2020 Reflection 273MK
2005 Dodge Ram 2500 CTD
Comment
-
Originally posted by Lonestar View Post
I agree about a clever design but there has to be an even better design where the motors could be accessed more easily. Definitely better access to the motor screw.
It seems that since the Schwintek system has now been used in trailers for several years, there would have been some attempt to make them more reliable overall. GDRV owns this problem, and they are the ones that should fix it or go with another mechanism on their trailers. I would not say that if it were just you and I having these issues, but it's lots of folks on the forums.
I also lube my gib and bearing block with CRC w PTFE and can hear and see the difference in its operation. A steel motor bushing running in an aluminum bearing block surely cannot help matters.
Jim
Comment
-
Jim,
You are probably right on the slide system. Guess I just got a little negative because of my recent issues. I've got my slide back up and running by myself by splicing and soldering my damaged control cable. And think I'll order a spare motor.
Lots of posts lately saying Lippert says no lube needed on slide assembly. Makes no sense to me as to how these parts can work long term without lubrication. I can't imagine what it could hurt unless one was in a very dirty environment causing dirt to adhere to the parts. Think I'll continue to lube as you do with CRC w PTFE.
I really have a difficult time getting the lube where I want it. Do you lube from behind the outside deal???
Jerry2020 Reflection 273MK
2005 Dodge Ram 2500 CTD
Comment
-
Originally posted by Lonestar View PostJim,
You are probably right on the slide system. Guess I just got a little negative because of my recent issues. I've got my slide back up and running by myself by splicing and soldering my damaged control cable. And think I'll order a spare motor.
Lots of posts lately saying Lippert says no lube needed on slide assembly. Makes no sense to me as to how these parts can work long term without lubrication. I can't imagine what it could hurt unless one was in a very dirty environment causing dirt to adhere to the parts. Think I'll continue to lube as you do with CRC w PTFE.
I really have a difficult time getting the lube where I want it. Do you lube from behind the outside deal???
Jerry
Yes I lube from outside and behind the seal. I could see if the bushing was a composite but steel on aluminum requires lubrication. Thinking if left dry and inactive long enough, it may even seize.
Jim
Comment
-
Well, this gets weird. Talked with Lippert this morning about identifying the motor in my trailer so I can get a spare. Seems there is an old 300rpm motor and a new 300rpm motor.
My trailer is only 2 years old and by my physical description of the motor to the young lady, she says I have the old motor. GD gave me a part number but unfortunately the old and new motor have the same number.
Now the problem. Lippert says you cannot mix the motors as they are slightly different gear ratios. If defective, you have to replace both motors.
Is there no end to this?2020 Reflection 273MK
2005 Dodge Ram 2500 CTD
Comment
Comment