Originally posted by Tiger6761
View Post
Announcement
Collapse
No announcement yet.
Leaking Kitchen Grey on Imagine 2400bh
Collapse
X
-
Forum moderators are not GD employees--we are volunteers and owners presumably just like yourself. Unless specifically mentioned otherwise, we have nothing to gain should you choose to purchase a product or engage a service we discuss on this forum.
Neil Citro
2018 Reflection 28BH Pepwave
2019 F350 6.7L Long Bed Crew Cab
-
-
So now what? Is that piece of pipe supposed to be glued in place up inside the pipe behind the sink? That is my guess, that we need to get this pipe out of the tank, heavily glue it in place and then push the tank back onto that pipe. Would love some input.
Comment
-
Originally posted by Tiger6761 View PostSo now what? Is that piece of pipe supposed to be glued in place up inside the pipe behind the sink? That is my guess, that we need to get this pipe out of the tank, heavily glue it in place and then push the tank back onto that pipe. Would love some input.
In the fourth pic (partially pasted in below) does that inserted pipe slide right out? Earlier in this thread it was mentioned that the fitting on the tank is a "slip joint". To me that implies the pipe should slide in and out.
Forum moderators are not GD employees--we are volunteers and owners presumably just like yourself. Unless specifically mentioned otherwise, we have nothing to gain should you choose to purchase a product or engage a service we discuss on this forum.
Howard & Francine
2017 Ford F-350 DRW, '19 315RLTSPlus
Comment
-
From the picture that Howard has above I would measure from the tank to the top of that pipe, then measure from the bottom of the floor to the inside lip where this pipe should seat and see if those measurements match. If the pipe is too short then that would cause the leaking that you are experiencing. Also that pipe pictured above should just pull out of the grommet installed in the tank, not sure how hard it is though. I also do not like the jagged edgs on that pipe, shotty work there in my opinion. It is also possible that the pipe connection above the floor was never made correctly, pipe and sink fitting not lining up.
BrianBrian & Michelle
2018 Reflection 29RS
2022 Chevy 3500HD
Comment
-
From the looks of that pipe it may have some type of build up on the bottom side preventing it from moving freely.
You might try using some type of soap or penetrating lubricant on the top edge and possibly using a slim flat object (feeler gauge type thing) to work the lubricant into the rubber grommet.Joseph
Tow Vehicle: 2024 GMC K3500 Denali Ultimate Diesel
Coach: 303RLS Delivered March 5, 2021
South of Houston Texas
Comment
-
New update. We are unable to get this dang pipe out of the grey tank. Admittedly I am dealing with tennis elbow in both arms so my strength isn’t what it normally would be. But this thing isn’t budging. Used silicone spray, got it worked in. We can push it down and it comes back up to a point and just stops. The screenshots I took make it look almost like that pipe is in the shape of a bell at the bottom. A very slight flair all around. And then the very end definitely has a flare going on. Not real sure what to do now. If this is the construction then no wonder it wasn’t seated in the connector above.
Have considered…
1. Drop a bead of silicone down in this gasket to solidify the pipe as far out as we can get it. Make it so when we go to set this thing we can push it home.
2. I have to take the whole gate valve connection apart to make a big enough hole. Push the pipe all the way through and fish it out. Then go get the right size pipe from the store. Cut it the right length. Glue it in the existing floor connection. Push the tank onto that.2 Photos
Comment
-
It gets deeper. I had to cut the pipe in order to push it down into the tank to get it out. In pic two that shows how that gasket is SUPPOSED to fit on the pipe. On mine that entire lower fitting was shoved through the gasket and was inside the tank. So not only was the pipe improperly glued, not seated properly in the vent pipe…. it was also WAY too long. So now we have to measure and see if we can get this right.2 Photos
Comment
-
That lip on the end is suspicious. Looks like someone tried to friction weld it to something else. I also looks like the end is slightly tapered between the bulge and the rest of the pipe (this is what I would have expected to make it easier to install in the bushing).
The only other thing I can think of would be a plastic test cap, but those are usually so thin they break out. https://www.firstsupply.com/Product/OAT33473Joseph
Tow Vehicle: 2024 GMC K3500 Denali Ultimate Diesel
Coach: 303RLS Delivered March 5, 2021
South of Houston Texas
Comment
-
We got this remounted finally. What a pain. We took off a good 3”-4” off the pipe because it was cut and mounted incorrectly in the first place. To get it mounted I used a little of that toilet seal conditioner to slick things up. It was tough. Getting screws lined up on the brackets was incredibly difficult. I think I am going to take some aluminum angle iron and make braces on each side of the tank so if anything ever comes loose again it shouldn’t rock right to left and put all the stress on the pipe. We still have to clean up the wiring and plumbing rat nest and get the belly back on but man this has been a job.
- Likes 1
Comment
Comment